IN STOCK!!! 

NEW V2.0 Version with Full POST Monitoring and CR3 Pro Rater Support. Also includes speed enhancements (2-3 minutes faster than JRP v1 !)

The new TX J-R Programmer V2 has been created to cater to the budget conscious and coded to work hand in hand with the latest version of the J-Runner app.

A third of the size of the TX NAND-X and optimized to run faster than any other USB-SPI based tool (Example Speeds: Others average 16M read 7m 20s, JRP v2 average 16M read 3mins), this nifty tool can fully read/write NAND over SPI, program CoolRunners or any Xilinx based RGH device over USB and also able to program onboard sounds using the TX SONUS 360 !

Complete with a CR JTAG cable so you simply plug 'n program without any soldering using the latest J-Runner App (needs to be at least Build 283). Also comes with NAND installation wires that have the connectors that are compatible with the NAND-X QSB boards. If you don't use the QSB's you can simply cut off the connectors and do a normal wires only install.

The J-R Programmer V2 is also fully upgradeable and can be programmed using the Xecuter X360USB PRO Update app. Onboard LED's indicate Power and BootLoader mode.

RED LED: Bootloader Mode (Switch to the left)
GREEN LED: J-R Programmer Mode (Switch to the right)
RED LED FLASHING: R/W Activity & POST Activity (Switch to the right)

Features:

• Fast NAND Programming
• Fast XILINX CR JTAG Programming
• Compatible with all CoolRunners inc the new CR3 Pro
• Supports Full Post Monitoring
• Compatible with both Phat and Slim
• Onboard LED's indicate Power & Data
• Easy Install System
• Compatible with All NAND-X QSB's
• Includes KIOSK option for Remote On
• Built-in Programmer For Future Firmware Upgrades
• Designed for the latest J-Runner App (Build 283+)
• Rock Solid Design – Tested by the J-Runner Team
• Supports New QSB V3 Kits (Solder Separately)
• Supports Sonus 360 Programming
• High Quality & Trusted TX Design

Contents:

• TX J-R Programmer V2
• Cable For QSB V3 Kit or Wires Install (QSB V3 Kits Sold Separately)
• Cable For Xilinx CRJTAG
• Cable for Xecuter Sonus 360 (Sonus 360 QSB Sold Separately – Trinity Kit or Corona Kit)

Those of you looking for a similar setup as the TX NAND-X RGH Edition V3, we recommend the following items that are available for purchase separately:

• TX USB to NAND-X cable
• TX NAND to COOLRUNNER Pin Header cable set
• Pin Headers
• TX SLIM POST QSB V1
• TX SLIM QSB Install Kit V1
• TX SLIM QSB Install Kit V2 (bundled POST QSB V1 and SLIM QSB Install Kit V1)
• TX 50Ohm Low Loss Double Shielded CPU_RST Cable for PHAT or SLIM

Disclaimer:

This device is designed primarily to aid or assist in the repair or replacement of defective hardware and also for the use of and development of legal open source software. It does not enable any kind of piracy or have any code whatsoever that circumvents any kind of protection. We do not support nor encourage, if possible, potential infringements of others intellectual property rights - please do not contact us with any question related to this use as we will not respond. DO NOT use or buy this product if you are looking to perform any illegal activity. Opening your Xbox 360 renders your warranty null and void. You should not attempt to repair your Xbox 360 unless it is no longer under warranty, or else you do NOT intend to use your warranty. MODCHIPCENTRAL.COM is not responsible for any damage done to your Xbox 360 or any other devices that you may use with this kit. Please do not attempt to repair your Xbox 360 unless you have experience working with computer hardware.

Xbox & Xbox 360 are registered trademarks by Microsoft Corporation. No affiliation between the TEAM XECUTER or MODCHIPCENTRAL.COM and Microsoft Corporation exists or is implied.