IN STOCK

 This board is a rebuild board, do you remember having to wire up the traces that you cut at the beginning of the MRA method to read the Liteon Firmware? well, this board can be used to avoid doing that re-wire, while the use of this board IS NOT REQUIRED to use the Vampire, we are sure that the use of this board will simplify the full mod procedure, and it has a couple of extra features like making easy access to the probe spots for the vampire and at the end of the job you can choose route the PIN 101 to the power connector of the drive for future updates without re-open (with an upcoming tool). Simply use the rebuild board from the beginning of the installation and we are sure you will find it useful.

This device will help to professional installers to do the Firmware reading on the latest Liteon drives (83850V2 & 93450). Its based on the MRA concept and 100% compatible with all Xtractor units, it connects directly on the Xtractor pin port. It came with 2 visual indicators, one for polarity check and other for Vendor Mode.This device release could confuse some people because we just released Litekey. This product no longer comes with the Foam pad.

Xilinx Parallel Programmer based on the popular Cable III with red and green indicators.

This programmer is an affordable and great way to program your Xilinx chips.
 
Start programming the Xilinx line of products including CPLD's and FPGA's!

Simply plug the programmer into your parallel port on your PC, an the other end to your Xilinx chip.
 

IN STOCK

This is the wires install cable for the NAND-X. Simply solder the wires to the correct points on the motherboard and plug into the NAND-X. Easy !

Preflashed USB SPI Nand Flashers based on Darkstar's Design.
Compatible with NandPro2.0b
Jumper to Enable Bootloader mode to allow updating of the PIC
Power LED
Removable jumper harness in case you want to leave it installed in your 360
Will also come with a CD containing the drivers and software.

PCI Sata controller. - Chipset VT6421A - 2x SATA and IDE ports! (Some have E-SATA some don'T, but E-ATA can not be used for reading the console drive)

 

Is your old Hitachi/Samsung/Benq System on its last legs ? Overheating and Freezing Issues ? 2 x Red Lights Crashing Your System ? THE ULTIMATE SOLUTION IS HERE !!!!!! 

The Xecuter xDrive Plus (inc xFan) is the next level in Xbox 360 cooling, stability and easy external firmware upgrading. The famous Team Xecuter have once again developed a solution to a very common problem on the older Xbox 360 consoles - the dreaded 2 x Red Lights and Overheating / Game Freezing issues.

Using the same technology as used on the original xDrive, you now have the ability to remove your internal 360 DVD ROM and have it connected to your 360 externally. The space where your internal DVD used to be is then replaced by an entire cooling system - as this is one of the main sources of heat inside the Xbox and it resides directly over the GPU (which is the main causes of overheating issues / game freezing / graphics corruption / rrod) - this now gives your Xbox a drop in temperature that is unprecedented in any of the cooling kits or fans that have ever been released before. In tests the GPU alone dropped as much as 20 Degrees Celsius with the xFan enabled !!! The entire system is completely custom designed from the ground up. It has been extensively tested by many users on the Xecuter forums and has shown to be a resounding success. One user reported that his console would give 2 Red Lights (Over heated) after 5 minutes even with the RROD Repair Kit installed and also with a Whisper Legacy Fan. When he installed the xDrive Plus and xFan - he tested the system overnight and finally turned it off manually after it had been running game demos for 20 hours straight !!! AMAZING RESULTS !!!

The new version is now able to read and program also the so called “big block NANDs” which are the 256Mb and 512Mb mainboard versions if the Xbox360. In addition to the added support for big blocks the new version ads more quicksolder pads which means less cables are required. Cygnos360 V2 Ref F fits nicely onto the underside of the Xbox360 mainboards and connects to the Jtag port via quicksolders (no resistors or cables needed here) Take a look at the photo, you will see on the top right the new quicksolder pads that sit directly on the jtag port.)

The ProgSkeet JTAG Injectus USB Programmer from the Infectus Team is the most advanced programmer for every ProgSkeet NAND / NOR / EEPROM USB Programmer or the ARGON and INFECTUS ModChip. It supports USB 2.0 and with the high professional programmer software can you easy reflash your ProgSkeet V1.0 and V1.1 or the ARGON chip. The ProgSkeet JTAG Injectus USB Programmer is the perfect complement for every ProgSkeet Developer!

IN STOCK

IN STOCK

This is for customers who ordered a caseless X360USB Pro from us previously and now want the case for it. 

Based on the GliGli Hack (a Reset type Glitch Hack), it works by sending precisely timed pulses to the console’s processor until the booting of unsigned code is successful. Once this has been achieved, XeLL, the Xenon Linux Loader is booted.

It works on Phat versions of the X360
(except Xenon motherboard) regardless of the Kernel version

Great for Glitching Phat consoles! Get the JRP V2 to program the Glitcher!

IN STOCK!  

ONLY fits TRINITY MOTHERBOARDS

We are proud to announce the MATRIX TRIDENT (PSI), the first TRIPLE NAND solution available for Xbox360.

The TRIDENT will transform your console 16 MB NAND in 3 independent 16 MB banks that can be read and write with any available SPI reader/writer solution using software tools like Nandpro 2.0 and Nandpro 3.0.

The trident can work together with any Glitcher solution present in the market.

A flat cable is supplied to directly connect it to the Matrix GLitcher II, for enhanced performances.

It features a quick solder board solution for the Trinity slim  and an external switch with led indicators to quickly choose which one of the THREE banks of NAND to use.

With the Matrix Trident you can assign one bank to the Original NAND, the second bank to boot a dashboard and the third NAND bank to boot Xell or a second dashboard.

Since there is no more AT90SUSBKEY Device kits available, other solutions are coming forward at a reasonable price but some people want the ATMEL Brand. This item is available via request only, so drop us an email and we will bring it in for you!


Use the Atmel FLIP software to load your compiled homebrew and development applications (HEX) directly into this USB dev kit via a standard computer USB port, no additional Hardware required!

Also some useful AVR USB Development Websites:

* avrfreaks.net
* fourwalledcubicle.com
* winavr.sourceforge.net
* avrtv.com

* Atmel FLIP Software Drivers - CLICK HERE

* Software Compatible With Windows 9x / Me / NT / 2000 / XP / Vista / 7 and Linux.

IN STOCK

New Version of Maximus AVR USB, the Maximus AVRUSB 1.2 comes with Case and standard USB Connection, Also due to main IC shortage we are switching our design from ATMEL 16KB to a PIC8F4550 32KB processor, which has proven to be easier to program and just as reliable as ATMEL.

Adaptor board to connect to progskeet one or two NAND CLIP SOLDERLESS.

It is necessary for PROGSKEET ACTEL FIRMWARE SOLDERLESS. Injectus is necessary for the re-programming of ACTEL (13/10/2011)

Contents:

• 1x Adaptor PCB
• 1x 50 pin FCC 8 cm cable
• 2x 32 pin FCC 20 cm cables

Presenting Minimus 32, a high quality production grade AVR USB Development Unit that is clean in design, low in cost and readily available to resellers around the globe. There are hundreds of projects available for the AVR USB hobbyist looking for a powerful yet cost effective solution. Works with Open Source LUFA USB firmware library and Open Source LibUSB software library.

The Minimus 32 AVR USB is powered by an Atmel AT90USB162 that is pre-programmed with the bootloader which allows code to be programmed inside the chip without any external programmer, just download the FLIP software from Atmel's web site and load your HEX code. To enter the bootloader mode you should simply press and hold HWB button, then press and release the RST button.

Black case for Minimus AVR / 32

After several design selections by the community, Xecuter have finally released a superbly designed case for the CK3 Lite.

Easy to fit with separate parts for the Eject & Modeb buttons along with a toggle switch, a superb little buy if you already own a CK3 Lite.

A precision built design with the quality that you expect from Team Xecuter