This is a genuine OEM Remote/LCD Screen replacement for the X360key/xk3y.

1 LEFT IN STOCK! ITS OUR TESTING UNIT

DISCONTINUED!

This is the EXACT MODEL and REVISION NUMBER that is required for the upcoming Burner Max firmware upgrade that everyone is asking about. The drives are stock and not upgraded in anyway. You can click the drop down list to add LT + to the drive!. The drive fits into a 5.25 Slot and is SATA and has a BLACK bezel.

A must for new XGD3 games so you can play on XBOX Live.

This is the new 4 position resistor - 4th value details will be added shortly.

This is the new Xecuter LT Switch v1.6 - the latest version in the #1 selling Xecuter LT Switch range.
Xecuter has designed a simple switch for all the Liteon drives that enables firmware full read/write. They have also included an ON/OFF Led to show correct operation when switching to 0x72 vendor mode.
Now Includes MULTI-R Function. After the discovery that a small number of Liteon drives would not dump the fw with a 20 ohm resistor - but required an 18 Ohm or 22 Ohm resistor - so you can now select between 18, 20 and 22 Ohms ! (Default should be set to 20 Ohms - this will work 99% of the time)

The installation is very simple and takes about 5 minutes if you have some small experience with a soldering iron. It has been tested with the latest Jungle Flasher 0.1.73. All Liteon drive versions have been tested with 100% Success (Including the troublesome Winbond IC). There is no need to remove the LT Switch after it has been installed - simply switch to normal mode and you are good to go. Even if you have to upgrade in the future - you don't have to touch the switch again !
Don't be fooled by more expensive copycat products. This is the only solution you need to do a very simple job. Remember this product follows the K.I.S.S engineering principle (KEEP IT SIMPLE STUPID) :)
The Only Liteon Solution Recommended By Team Jungle !
Enables Read/Write on ALL Liteon 74850, 83850, 93450 DVD Drives
Easy & Simple Install - Install Once & Forget
Enable / Disable Switch
Multi-R Switch (18, 20, 22 Ohms)
On/Off LED
Completely Undetectable
No Need To Uninstall
Works with ALL tools including the latest Jungle Flasher


This device is designed primarily to aid or assist in the repair or replacement of defective hardware and also for the use of and development of legal open source software. It does not enable any kind of piracy or have any code whatsoever that circumvents any kind of protection. We do not support nor encourage, if possible, potential infringements of others intellectual property rights - please do not contact us with any question related to this use as we will not respond. DO NOT use or buy this product if you are looking to perform any illegal activity.

Simple 1 wire one solder install speaker for Maximus Lizard Speaker

A new replacement DVD-ROM drive for Xbox 360 by Toshiba-Samsung, model MS28. As Microsoft Xbox 360 requires a key from your board for the drive to work, you will have to flash the drive with this key for it to function.

Based on the GliGli Hack (a Reset type Glitch Hack), it works by sending precisely timed pulses to the console’s processor until the booting of unsigned code is successful. Once this has been achieved, XeLL, the Xenon Linux Loader is booted.

It works on Phat versions of the X360
(except Xenon motherboard) regardless of the Kernel version

Great for Glitching Phat consoles! Get the JRP V2 to program the Glitcher!

IN STOCK!  

After several design selections by the community, Xecuter have finally released a superbly designed case for the CK3 Lite.

Easy to fit with separate parts for the Eject & Modeb buttons along with a toggle switch, a superb little buy if you already own a CK3 Lite.

A precision built design with the quality that you expect from Team Xecuter

Xecuter have released the latest in their line of LT Switch Liteon DVD mod products, the LT Clip + LT Switch v2.

This kit has been designed with the beginner in mind. It's been in development for a while due to the absolute precision and stability needed to make sure it works for the the lifetime of the DVD Drive with no soldering or glue for trace repairs. There is even included a built in continuity tester to make sure your trace cuts are perfect !

Also Includes MULTI-R Function. After the discovery that a small number of Liteon drives would not dump the fw with a 20 ohm resistor - but required an 18 Ohm or 22 Ohm resistor -  so you can now select between 18, 20 and 22 Ohms ! (Default should be set to 20 Ohms - this will work 99% of the time)

This is the first and only Liteon solution where there is 100% No Soldering & No Glue - The fastest and easiest "MRA Hack" product on the market.

The Only Liteon Solution Recommended By Team Jungle !

• Unique designed clip
• No Solder & No Glue
• External LT Switch
• Built in continuity tester to make sure your trace cuts are perfect
• Enables Read/Write on ALL Liteon 74850, 83850, 93450 DVD Drives
• Easy & Simple Install - Install Once & Forget
• Enable / Disable Switch
• Multi-R Switch (18, 20, 22 Ohms)
• On/Off LED
• Completely Undetectable
• Requires Xecuter CK3 Pro or Xecuter CK3 Lite to connect the LT Switch v2 to the Liteon DVD Drive
• No Need To Uninstall
• Works with ALL tools including the latest Jungle Flasher
  
• Full Installation Tutorial - CLICK HERE

The new version is now able to read and program also the so called “big block NANDs” which are the 256Mb and 512Mb mainboard versions if the Xbox360. In addition to the added support for big blocks the new version ads more quicksolder pads which means less cables are required. Cygnos360 V2 Ref F fits nicely onto the underside of the Xbox360 mainboards and connects to the Jtag port via quicksolders (no resistors or cables needed here) Take a look at the photo, you will see on the top right the new quicksolder pads that sit directly on the jtag port.)

Is your old Hitachi/Samsung/Benq System on its last legs ? Overheating and Freezing Issues ? 2 x Red Lights Crashing Your System ? THE ULTIMATE SOLUTION IS HERE !!!!!! 

The Xecuter xDrive Plus (inc xFan) is the next level in Xbox 360 cooling, stability and easy external firmware upgrading. The famous Team Xecuter have once again developed a solution to a very common problem on the older Xbox 360 consoles - the dreaded 2 x Red Lights and Overheating / Game Freezing issues.

Using the same technology as used on the original xDrive, you now have the ability to remove your internal 360 DVD ROM and have it connected to your 360 externally. The space where your internal DVD used to be is then replaced by an entire cooling system - as this is one of the main sources of heat inside the Xbox and it resides directly over the GPU (which is the main causes of overheating issues / game freezing / graphics corruption / rrod) - this now gives your Xbox a drop in temperature that is unprecedented in any of the cooling kits or fans that have ever been released before. In tests the GPU alone dropped as much as 20 Degrees Celsius with the xFan enabled !!! The entire system is completely custom designed from the ground up. It has been extensively tested by many users on the Xecuter forums and has shown to be a resounding success. One user reported that his console would give 2 Red Lights (Over heated) after 5 minutes even with the RROD Repair Kit installed and also with a Whisper Legacy Fan. When he installed the xDrive Plus and xFan - he tested the system overnight and finally turned it off manually after it had been running game demos for 20 hours straight !!! AMAZING RESULTS !!!

PCI Sata controller. - Chipset VT6421A - 2x SATA and IDE ports! (Some have E-SATA some don'T, but E-ATA can not be used for reading the console drive)

 

Preflashed USB SPI Nand Flashers based on Darkstar's Design.
Compatible with NandPro2.0b
Jumper to Enable Bootloader mode to allow updating of the PIC
Power LED
Removable jumper harness in case you want to leave it installed in your 360
Will also come with a CD containing the drivers and software.

This item is the vampire, cable to xtractor pro and protective pad only.
This does not include the rebuild